HOSE ASSEMBLY

HOSE
2 ½" Seawater Hose, 50' Lengths

NOTE CHANGE - 

• SUPPLIER MUST PROVIDE WRITTEN CERTIFICATION THAT HOSE ASSEMBLIES (HOSE AND FITTING) HAVE BEEN HYDROSTATICALLY TESTED AT 600 PSIG WITH CLEAN, FRESH WATER FOR 30 MINUTES WITH ZERO LEAKS AND/OR BULDGES.

HOSE ASSEMBLY MUST BE MANUFACTURED USING COMPONENTS
FROM ONE MANUFACTURER. HOSE ASSEMBLIES ARE TO BE
ORDERED USING THE TECHNICAL SPECIFICATIONS OUTLINED
BELOW.
EACH HOSE ASSEMBLY IS TO BE IN LENGHTS OF 50 FEET AND
EQUIPPED WITH IDENTICAL MALE NPT FTGS ON EACH END.
ASSEMBLIES MUST BE PROVIDED USING AEROQUIP PART NUMBER
2651-40 OR AE 369 FOR THE HOSE AND PART NUMBER 44- 412-40-40
FOR THE FITTINGS OR EQUAL.
NOTE: THE HOSE IS NOT LIMITED TO AEROQUIP. ANY OTHER
COMPANY THAT COMPLIES WITH THE SALIENT CHARACTERISTICS
LISTED BELOW MAY BE CONSIDERED.
SALIENT CHARACTERISTICS FOR HOSE:
1.OUTSIDE DIAMETER 2.875 INCHES
2. INSIDE DIAMETER 2.375 INCHES
3. BURST TEST PRESSURE 1400 PS
4. HYDRO TEST PRESSURE 700 PSI
5. MAXIMUM OPERATING PRESSURE 350 PSI
6. MINIMUM INSIDE BENDING RADIUS 24 INCHES
7. INNER CONVEYING TUBE MATL RUBBER SYNTHETIC
LAYER COMPOSITION 1st LAYER OF BRAIDED TEXTILE YARN
LAYER COMPOSITION 2nd LAYER BRAIDED STEEL WIRE
LAYER COMPOSITION 3rd LAYER BRAIDED TEXTILE YARN
8. OUTER LAYER MOLDED RUBBER, SYNTHETIC
SALIENT CHARACTERISTICS FOR HOSE ADAPTER (TWO PER HOSE
SECTION) 1. CONNECTION TYPE 1st END THROED EXTERNAL HOSE
GRIPPING
2. CONNECTION TYPE 2nd END THROED EXTERNAL PIPE
3. MAX OPERATING PRESSURE 350 PSI
4. NOMINAL THRO SIZE 2.500 INCHES
5. NOMINAL PIPE SIZE ACCOMMODATED 2.500 INCHES
6. SEAT ANGLE 30 DEGREES
7. MATERIAL COPPER ALLOY
8. THRO SERIES DESIGNATOR NPTF, FURNISHED ITEM 1 COUPLING

This is a combined synopsis/solicitation for commercial items prepared in accordance with the
information in FAR Subpart 12.6, as supplemented with additional information included in this
notice. This announcement constitutes the only solicitation; a written solicitation will not be
issued. PAPER COPIES OF THIS SOLICITATION WILL NOT BE AVAILABLE. This
combined synopsis/solicitation SHALL be posted on SAM.GOV.
The solicitation documents and incorporates provisions and clauses in effect through Federal
Acquisition Circular 2022-04 and DFARS Change Notice 20211230. It is the responsibility of
the contractor to be familiar with the applicable clauses and provisions. The clauses may be
accessed in full text at these addresses: https://www.acquisition.gov/far and http://
www.acq.osd.mil/dpap/dars/dfarspgi/current/.
The NAICS code is 326220 and the Small Business Size Standard is 750 employees. The
proposed contract action is set-aside for small business concerns. The proposed contract action is
for commercial items for which the Government intends to award a Single Award contract with
Firm Fixed-price provisions, under the authority of FAR Subpart 13.5.
Interested persons may identify their interest and capability to respond to the requirement or
submit proposals. All bids, proposals, or quotations received by the closing response date may be
considered by the Government.
1. Solicitation Number: SPMYM1-22-Q-0012
2. Solicitation Issue Date: 01 MARCH 2022
3. Contract Specialist: Angela Goldsmith
4. Quote Due Date/Local Time: 11 March 2022 5:00 PM EST. All quotes must be
submitted electronically to Angela.Goldsmith@DLA.MIL by the quote due date above. The
email subject field shall contain the solicitation number. The email body shall include the
Contractor name, address, phone number, and email address.
PAPER COP Y QUOTES WILL NOT BE ACCEPTED.
5. SITE VISIT: There will be no site visit for this requirement.
6. Questions: All questions shall be in writing and e-mailed to
Angela.Goldsmith@DLA.MIL Questions concerning this solicitation will be accepted up to the
Close of Business (1500 EST) on 8 March 2022. DLA Maritime does not commit to providing
responses to questions submitted after this date; however, attempts to answer questions will be
made. If needed a solicitation amendment will be posted by 10 March 2022.HOSE