Roofing Replacement at Hannibal Locks and Dam

The U.S. Army Corps of Engineers (USACE), Pittsburgh District intends to procure a construction project that involves the roofing replacement at Hannibal Locks and Dam, Monroe County, Hannibal Ohio. The contract generally includes the removal and replacement of nine (9) machinery house roofs, one (1) middle wall pier roof, and one (1) land wall pier roof. These eleven (11) roofs are located on the service bridge of Hannibal Lock and Dam.

In general, the tasks required in the performance of this contract include:

Land Wall Pier Roof:

• Removal of existing built up roof, ballast, aluminum flashing, and roof drain from a 9 ft by 14 ft flat roof. 
• Repair any damage to the existing concrete roof deck making and based on existing conditions, tapered insulation may need to be installed to provide positive drainage towards the existing roof drain. 
• Replace any sections of the 3-1/2” cant strip with nailable lightweight concrete. 
• Install new fully adhered, 90 mil EPDM roofing system, conforming to ASTM D4637/D4637M. 
• Install new roof drain with dome and removable sediment trap connected to the existing 3” threaded outlet.
• Install new 1/8” aluminum flashing to provide a watertight seal from the existing 6” aluminum fascia to the new rubber membrane. It is assumed two separate flashing pieces will be needed due to the geomerty of the existing roof and the existing 3-1/2” cant strip. See Figure A for the flashing details of the existing roof. 
• Install new permanent fall protection system for use as part of the contractor’s personal fall arrest system that permits access to the entire roof for 2 people. 

Middle Wall Pier Roof:

• Removal of existing built up roof, ballast, aluminum flashing, and roof drain from a 12 ft 2 inch by 11 ft 2 inch flat roof. 
• Remove and reinstall the existing lightning protection system on the roof.
• Repair any damage to the existing concrete roof deck making and based on existing conditions, tapered insulation may need to be installed to provide positive drainage towards the existing roof drain. 
• Replace any sections of the 3-1/2” cant strip with nailable lightweight concrete. 
• Install new fully adhered, 90 mil EPDM roofing system, conforming to ASTM D4637/D4637M. 
• Install new roof drain with dome and removable sediment trap connected to the existing 3” threaded outlet.
• Install new 1/8” aluminum flashing to provide a watertight seal from the existing 6” aluminum fascia to the new rubber membrane. It is assumed two separate flashing pieces will be needed due to the geomerty of the existing roof and the existing 3-1/2” cant strip. See Figure A for the flashing details of the existing roof.   
• Install new permanent fall protection system for use as part of the contractor’s personal fall arrest system that permits access to the entire roof for 2 people. 

Machinery House Roofs Pier 1 and Pier 9:

• Removal of existing built up roof, ballast, aluminum flashing, and roof drain from a 21 ft 4-1/2 inch by 27 ft 6 inch flat roof. 
• Replacement of the arched acrylic plastic skydomes with a new skylight system. 
• Inspect and replace any damaged wood as part of the 2 inch by 8 inch wooden curb. 
• Inspect and replace any cant strips on the roof and around the wooden curb.
• Repair any damage to the existing concrete roof deck making and based on existing conditions, tapered insulation may need to be installed to provide positive drainage towards the existing roof drain. 
• Install new fully adhered, 90 mil EPDM roofing system, conforming to ASTM D4637/D4637M. 
• Install one new roof drain with dome and removable sediment trap connected to the existing 3” threaded outlet.
• Install new 24 gauge aluminum flashing to provide a watertight seal from the existing aluminum reglet over the new ruber membrane roof. See Figure C for the flashing details of the existing roof.  
• Install new permanent fall protection system for use as part of the contractor’s personal fall arrest system that permits access to the entire roof for 2 people. 

Machinery House Roofs Pier 2 thru Pier 8:

• Removal of existing built up roof, ballast, aluminum flashing, and roof drain from a 30 ft 9 inch by 27 ft 6 inch flat roof. 
• Replacement of the arched acrylic plastic skydomes with a new skylight system. 
• Inspect and replace any damaged wood as part of the 2 inch by 8 inch wooden curb. 
• Inspect and replace any cant strips on the roof and around the wooden curb.
• Repair any damage to the existing concrete roof deck making and based on existing conditions, tapered insulation may need to be installed to provide positive drainage towards the existing roofing drains. 
• Install new fully adhered, 90 mil EPDM roofing system, conforming to ASTM D4637/D4637M. 
• Install two new roof drains with dome and removable sediment trap connected to the existing 3” threaded outlet.
• Install new 24 gauge aluminum flashing to provide a watertight seal from the existing aluminum reglet over the new ruber membrane roof. See Figure C for the flashing details of the existing roof.    
• Install new permanent fall protection system for use as part of the contractor’s personal fall arrest system that permits access to the entire roof for 2 people. 

The work shall be completed within 270 calendar days after written Notice to Proceed.

In accordance with FAR 36.204 and DFARS 236.204, the estimated magnitude of this construction project is:  Between $250,000 to $500,000. 

The Government is planning a pre-bid site visit; the date and time will be in the solicitation.

All *responsible Offerors are encouraged to participate. The IFB will be issued on or about 08 December 2022, online through Procurement Integrated Enterprise Environment (PIEE) which posts the opportunity to SAM.gov; therefore, requests for hardcopies of the solicitation package will not be honored.

*Responsible means a contractor that meets the standards in FAR 9.104 - available at https://www.acquisition.gov

In order to submit a Bid on this project, your company must –

1. Be registered in System for Award Management (SAM) and maintain an active registration status.
2. Be registered in the Procurement Integrated Enterprise Environment (PIEE) for the Solicitation Module with the PROPOSAL MANAGER role.

System for Award Management (SAM) Registration

Registering in SAM.gov includes both entity validation and entity registration.

To register in SAM:

            a. Navigate to SAM.gov

            b. Select Sign-In (top right)

            c. Select Create an Account then Follow the Instructions.

            d. After Account is Set-up, Select Sign In.

            e. Under the Entity Management widget, Select “Get Started” button.

f. Select Register Entity. As part of entity registration, a Unique Entity ID will  be assigned.

For Additional Information on SAM:

To Register Your Entity (company) or check Your Registration status, please visit https:/www.fsd.gov/gsafsd_sp?id=gsa_index .  Under the heading of “Learn How to Register Your Entity”, you will find the following,

            Get Started with Your Registration

            Check Registration Status - ACTIVE, INACTIVE, PENDING

            Update Your Registration

            Become an Entity Administrator

            Validate Your Entity

            *Access User Guides

*By selecting this option, you can obtain a Quick Start Guide for Contract Registrations.

Also, on this site, in the search block, you can perform key words searches such as User Guides - FAQs, Videos, and Definitions.

PLEASE NOTE

It is mandatory that all companies be registered in SAM in order to receive federal contracts. There is no charge to register or maintain your company (entity) registration.

Login.gov manages usernames and passwords for SAM.gov.

*Important* Registration Information

Registration can take at least ten (10) business days to be active in SAM.gov.

Registration must be in active status upon offer submission and remain active during award period.

Registration must be renewed every 365 days to remain active.

The Federal Service Desk (FSD) for SAM questions, may be contacted.

Phone Number: 866-606-8220

Hours of Operation: Monday-Friday 8 a.m. to 8 p.m. ET

Procurement Integrated Enterprise Environment (PIEE) Solicitation Module Registration

To register for PIEE follow the below instructions.

            Register in PIEE:

                        a. Navigate to https://piee.eb.mil/

                        b. Select Register [top right]

                        c. Select Vendor

                        d. Create a User ID and Password and follow the prompts [next]

                        e. Create Security Questions [next]

                        f. Complete your User Profile Information [next]

                        g. Complete your Supervisor or Approving Official Information [next]

                        h. Complete Roles

                        i. Step 1. Select SOL-Solicitation

                        ii. Step 2. Select Proposal Manager

                        iii. Step 3. Click Add Roles

                        iv. Step 4. Fill in your Location Code (CAGE Code) [next]

                        i. Provide a justification for your registration [next]

                        j. Follow the remaining prompts to submit your registration

The Electronic Business Service Desk for PIEE questions, may be contacted.

Phone Number: 866-618-5988

Hours of Operation: Monday-Friday 06:30 - 24:00 EST

Email: disa.global.servicedesk.mbx.eb-ticket-requests@mail.mil

If you would like to learn about doing business with USACE, please visit

https://www.usace.army.mil/Business-With-Us/