EXPANSION JOINTS

The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract for the items listed below. The required items are for commercial items prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice.

The Contract Line Items (CLINs) are as follows:

CLIN 0001- 40528354 EXPANSION JOINT (DRILLED X UNDRILLED) 42" X 12"FF,

UNAFLEX P/N: 1E1NN42X12NZAND HYDROTEST P/N: HT42 IS INCLUDED IN PRICE

MIL-E-15330D, CLASS A, TYPE 1, ORDERING DATA MIL-E-15330D

EXPANSION JOINT INFORMATION, ID=42", OD=S0-1/4", FACE TO FACE 12", BOLT CIRCLE 47-3/4", NUMBER OF HOLES 38, DIA. OF HOLES 1-5/16

QUANTITY: 1 EA

ORDERING DATA

(A) EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT

1977, AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(B) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(D) ONE (1) EA 42.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 38 BOLT

HOLES, 1-5/16" DIA HOLES ON A 47-3/4" BOLT CIRCLE.

(E) N/A

(F) SPECIFIC ARCH CONSTRUCTION NOT REQD

(G) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(H) VACUUM TEST NOT REQUIRED

(I) SPECIAL PACKAGING NOT REQUIRED

(J) SPECIAL PACKING NOT REQUIRED

(K) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

CLIN 0002-40528355 EXPANSION JOINT (DRILLED X UNDRILLED) 28" X 12 FF",

MIL-E-15330D, CLASS A, TYPE 1, UNAFLEX P/N: 1E1NN28X12NU AND

HYDROTEST P/N: HT28 IS INCLUDED IN THE PRICE ORDERING DATA MIL-E-15330D AND SOURCES ATTACHED

EXPANSION JOINT INFORMATION: ID=28, OD=34-11/16, FACE TO FACE 12", BOLT CIRCLE 32-7/16, NUMBER OF HOLES 32, DIA. OF HOLES 1-3/16

QUANTITY: 1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(B) ONE (1) EA 28.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 32 BOLT

HOLES, 1-3/16" DIA HOLES ON A 32-7/16" BOLT CIRCLE.

(C) N/A

(D) SPECIFIC ARCH CONSTRUCTION NOT REQD

(E) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(F) VACUUM TEST NOT REQUIRED

(G) SPECIAL PACKAGING NOT REQUIRED

(H) SPECIAL PACKING NOT REQUIRED

(I) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

CLIN 0003- 40528356 EXPANSION JOINT (DRILLED X UNDRILLED) 46" X 12 FF", UNAFLEX P/N: 1E1NN46X12NZAND HYDROTEST P/N: HT46 IS INCLUDED IN THE PRICE

MIL-E-15330D, CLASS A, TYPE 1, ORDERING DATA MIL-E-15330D

EXPANSION JOINT INFORMATION, ID=46", OD=54-1/2", FACE TO FACE 12", BOLT CIRCLE 52", NUMBER OF HOLES 42, DIA. OF HOLES 1-5/16

QUANTITY: 1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(B) DRILLING REQUESTED ON ONE FLANGE , PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(C) ONE (1) EA 46.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 42 BOLT

HOLES, 1-5/16" DIA HOLES ON A 52.00" BOLT CIRCLE.

(D) N/A

(E) SPECIFIC ARCH CONSTRUCTION NOT REQD

(F) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(G) VACUUM TEST NOT REQUIRED

(H) SPECIAL PACKAGING NOT REQUIRED

(I) SPECIAL PACKING NOT REQUIRED

(J) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

CLIN 0004- 40528357 EXPANSION JOINT (DRILLED X UNDRILLED) 28" X 12 FF",

MIL-E-15330D, CLASS A, TYPE 1, UNAFLEX P/N: 1E1NN28X12NU AND

HYDROTEST P/N: HT28 IS INCLUDED IN THE PRICE ORDERING DATA MIL-E-15330D

EXPANSION JOINT INFORMATION: ID=28, OD=34-11/16, FACE TO FACE 12", BOLT CIRCLE 32-7/16, NUMBER OF HOLES 32, DIA. OF HOLES 1-3/16

QUANTITY:1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(B) ONE (1) EA 28.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 32 BOLT

HOLES, 1-3/16" DIA HOLES ON A 32-7/16" BOLT CIRCLE.

(C) N/A

(D) SPECIFIC ARCH CONSTRUCTION NOT REQD

(E) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(F) VACUUM TEST NOT REQUIRED

(G) SPECIAL PACKAGING NOT REQUIRED

(H) SPECIAL PACKING NOT REQUIRED

(I) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

CLIN 0005- 40518190 EXPANSION JOINT (DRILLED X UNDRILLED) 28" X 12" FF, MIL-E-15330D, CLASS A, TYPE 1, UNAFLEX P/N: 1E1NN28X12NU AND HYDROTEST P/N: HT28, INCLUDED IN PRICE ORDERING DATA MIL-E-15330D

QUANTITY : 1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(B) ONE (1) EA 28.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 32 BOLT

HOLES, 1-3/16" DIA HOLES ON A 32-7/16" BOLT CIRCLE.

(C) N/A

(D) SPECIFIC ARCH CONSTRUCTION NOT REQD

(E) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(F) VACUUM TEST NOT REQUIRED

(G) SPECIAL PACKAGING NOT REQUIRED

(H) SPECIAL PACKING NOT REQUIRED

(I) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

NOTES:

1) NNSY ACKNOWLEDGES CANCELLATION OF MIL-E-15330D, HOWEVER, THIS

SPECIFICATION IS INVOKED FOR THIS PROCUREMENT AND ITS APPLICATION.

2) UNAFLEX INC AND LA FAVORITE INDUSTRIES ARE THE ONLY TWO APPROVED

MANUFACTURERS. ANY OTHER MANUFACTURER MUST BE APPROVED BY CODE

261 ENGINEERING. POC: CHRIS GILL @ 396-3164/65/66.

CLIIN 0006- 40518192 XPANSION JOINT (DRILLED X UNDRILLED) 28" X 12",FF

MIL-E-15330D, CLASS A, TYPE 1, UNAFLEX P/N: 1E1NN28X12NU AND HYDROTEST P/N: HT28 IS INCLUDED IN THE PRICE ORDERING DATA MIL-E-15330D AND SOURCES ATTACHED

EXPANSION JOINT INFORMATION: ID=28, OD=34-11/16, FACE TO FACE 12", BOLT CIRCLE 32-7/16, NUMBER OF HOLES 32, DIA. OF HOLES 1-3/16

QUANTITY : 1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(B) ONE (1) EA 28.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 32 BOLT

HOLES, 1-3/16" DIA HOLES ON A 32-7/16" BOLT CIRCLE.

(C) N/A

(D) SPECIFIC ARCH CONSTRUCTION NOT REQD

(E) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(F) VACUUM TEST NOT REQUIRED

(G) SPECIAL PACKAGING NOT REQUIRED

(H) SPECIAL PACKING NOT REQUIRED

(I) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

NOTES:

1) NNSY ACKNOWLEDGES CANCELLATION OF MIL-E-15330D, HOWEVER, THIS

SPECIFICATION IS INVOKED FOR THIS PROCUREMENT AND ITS APPLICATION.

2) UNAFLEX INC AND LA FAVORITE INDUSTRIES ARE THE ONLY TWO APPROVED

MANUFACTURERS. ANY OTHER MANUFACTURER MUST BE APPROVED BY CODE

261 ENGINEERING. POC: CHRIS GILL @ 396-3164/65/66.

CLIN 0007- 40518193 XPANSION JOINT (DRILLED X UNDRILLED) 46" X 12" FF, UNAFLEX P/N: 1E1NN46X12NZAND HYDROTEST P/N: HT46 IS INCLUDED IN THE PRICE MIL-E-15330D, CLASS A, TYPE 1 ORDERING DATA MIL-E-15330D EXPANSION JOINT INFORMATION, ID=46", OD=54-1/2", FACE TO FACE 12", BOLT CIRCLE 52", NUMBER OF HOLES 42, DIA. OF HOLES 1-5/16

QUANTITY: 1 EA

ORDERING DATA

EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT 1977,

AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(A) CLASS A, TYPE 1

(B) DRILLING REQUESTED ON ONE FLANGE , PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(C) ONE (1) EA 46.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 42 BOLT

HOLES, 1-5/16" DIA HOLES ON A 52.00" BOLT CIRCLE.

(D) N/A

(E) SPECIFIC ARCH CONSTRUCTION NOT REQD

(F) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(G) VACUUM TEST NOT REQUIRED

(H) SPECIAL PACKAGING NOT REQUIRED

(I) SPECIAL PACKING NOT REQUIRED

(J) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

NOTES:

1) NNSY ACKNOWLEDGES CANCELLATION OF MIL-E-15330D, HOWEVER, THIS

SPECIFICATION IS INVOKED FOR THIS PROCUREMENT AND ITS APPLICATION.

2) UNAFLEX INC AND LA FAVORITE INDUSTRIES ARE THE ONLY TWO APPROVED

MANUFACTURERS. ANY OTHER MANUFACTURER MUST BE APPORVED BY CODE 261

ENGINEERING. POC: MIKE BRADSHAW@ 396-3164/65/66.

CLIN 0008- 40518194 EXPANSION JOINT (DRILLED X UNDRILLED) 42" X 12" FF,

UNAFLEX P/N: 1E1NN42X12NZAND HYDROTEST P/N: HT42 IS INCLUDED IN PRICE MIL-E-15330D, CLASS A, TYPE 1, ORDERING DATA MIL-E-15330D EXPANSION JOINT INFORMATION, ID=42", OD=50-1/4", FACE TO FACE 12", BOLT CIRCLE 47-3/4", NUMBER OF HOLES 38, DIA. OF HOLES 1-5/16

QUANTITY: 1 EA

ORDERING DATA

(A) EXPANSION JOINT, NONMETALLIC FIRE RETARDANT, MIL-E-15330D DTD 14 OCT

1977, AMEND 1 DTD 23 JAN 1978 AND NOTICE 1 DTD 16 FEB 1989

(B) CLASS A, TYPE 1

(C) DRILLING REQUESTED ON ONE FLANGE, PER EXPANSION JOINT. THE REMAINING

FLANGE WILL BE DRILLED AT THE TIME OF INSTALLATION.

(D) ONE (1) EA 42.00" NPS X 12.00" FACE TO FACE. DRILLING REQUIREMENTS: 38 BOLT

HOLES, 1-5/16" DIA HOLES ON A 47-3/4" BOLT CIRCLE.

(E) N/A

(F) SPECIFIC ARCH CONSTRUCTION NOT REQD

(G) PROOF OF HYDROSTATIC TESTING REQUIRED PER 3.5 AND 4.6.4. JOINTS SHALL BE

TESTED TO 75 PSI FOR 10 MINUTES

(H) VACUUM TEST NOT REQUIRED

(I) SPECIAL PACKAGING NOT REQUIRED

(J) SPECIAL PACKING NOT REQUIRED

(K) SPECIAL CASE MARKING NOT REQUIRED

*DRILLED RETAINING RINGS REQUIRED

NOTES:

1) NNSY ACKNOWLEDGES CANCELLATION OF MIL-E-15330D, HOWEVER, THIS

SPECIFICATION IS INVOKED FOR THIS PROCUREMENT AND ITS APPLICATION.

2) UNAFLEX INC AND LA FAVORITE INDUSTRIES ARE THE ONLY TWO APPROVED

MANUFACTURERS. ANY OTHER MANUFACTURER MUST BE APPROVED BY CODE

261 ENGINEERING. POC: CHRIS GILL@ 396-3164/65/66.

The requirement will be solicited as a total small business set aside. The NAICS code applicable to this procurement is 326122, Plastics Pipe and Pipe Fitting Manufacturing with a size standard of 500. The Product Service Code is 4730, Plastics Pipe and Pipe Fitting Manufacturing.

The anticipated delivery date for this acquisition is 30 days after contract award. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. THE SOLICITATION IS NOT YET AVAILABLE.

The solicitation number is SPMYM123Q0095, and it is expected to be available on or about 26 APRIL 2024 TO 3 MAY2024 and posted to SAM.gov, https://sam.gov/  Quotes will be due by 1:00 PM EST on 03 MAY 2024. Responses to the solicitation notice shall be emailed to the attention of Sheree McDonnell at sheree.mcdonnell@dla/mil. Please make sure that the solicitation number (SPMYM123Q0095) is included in the subject line of any email correspondence. Emails without subject lines will not be read because of security issues.

Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offeror's to access solicitation documents posted. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed.

All responsible sources may submit a proposal which may be considered by the Government. By submitting a quote, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the solicitation, except for awards to foreign vendors for work to be performed outside the United States. Lack of registration in the SAM database will make an offeror ineligible for award. Offerors may obtain information on registration and annual confirmation requirements by calling 1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in accordance with the solicitation, dates, and procedures. Please direct all questions regarding this requirement to Sheree McDonnell at sheree.mcdonnell@dla/mil..